Anachostic

Brainfield studio is down at the moment for renovations.  This is the big push to bring everything online and together, and it’s led me to realize some things that will pain me for a bit.

First, I have a lot of gear.  And up until this point, I had been using it piecemeal and never really had to worry much about connections.  To accommodate it all, I need a lot more connections.  That means lots of wires.  Lots of them.

So to sort of map it all out, the final design will have a 6-keyboard stand, a 4-keyboard stand, and a 2-keyboard stand.  Then there is the rack and mixer, and the monitors.  All of the rackmount devices can be considered one unit as they have a submixer.  So that’s 13 stereo inputs, or 26 channels.  I have a 16 channel mixer.  How will I reconcile that?  Time to level up the studio with a patchbay.

The patchbay sits between connections and lets you override any at will.  So I can have my usual favorite devices connected and if I need to hear a different device, I can patch its output in the patchbay to a free input on the mixer.  It takes a little bit to wrap your head around, but I’m getting to the point that I can’t imagine not doing it this way.  The alternative is having a bunch of cable ends laying on the floor around the mixer and I have to figure out which one I need, unplug something from the mixer and then plug in what I want. It’s also a lot of wear and tear on the mixer ports.

So that sounds lovely, but now, consider what I said, the patchbay sits between every connection.  So while you used to have a connection between the device and the mixer, now you have a connection from the device to the patchbay, and another from the mixer to the patchbay.  That’s more wires.  With my 16 channel mixer, that’s going to be 8 stereo cables, plus the monitor outs.  Because the monitors connect to the patch bay and the mixer outputs connect to the patchbay.  Everything connects to the patchbay.

I have options in which patchbay I choose.  I decided to bite the bullet and buy one that uses TRS (tip ring sleeve), which is functionally equivalent to a stereo jack.  Biting that bullet means that all of my existing mono cables are worthless.  Well, I can still use a mono cable I suppose, but I will be running each port as stereo and I’ll need to buy new TRS to dual mono cables.  That’s going to be pricey.  And on top of those, I also have to buy TRS cables to do the patching on the patchbay.

So there’s that.  That’s the first point.  The second point is:  I have a lot of gear.  It’s not only audio signals I have to concern myself with, it’s also MIDI control.  So I’ll have a few input devices and whole lot of controlled devices.  I have just maxed out my MIDI interface hardware, so I have 9 in and 9 out ports, which is far more than I probably need.  Why so many ports?  Because some devices can be multitimbral and can listen on all 16 channels so they need their own dedicated port.  Monotimbral devices can share a port and each use a unique channel number.  And to accomplish that, I’ll be using MIDI thru boxes to split the signal.  That means I don’t have to have all the devices on for the signal to pass through each one.

But you know what that means, more cables!  And with the added devices spread around the room, I need more cables and longer cables.  So I made up a rough list of what I need to buy to connect everything together.

Audio Cables (TRS to dual 1/4”, aka Insert cable):

• 3’ – 8
• 15’– 11

Audio Cables (TRS-TRS)

• 25’ – 2

TRS Y adapters – 2

TRS Patchbay cables – 6

MIDI Cables

• 6’ – 1
• 15’ – 4
• 25’ – 4

I placed an order with MonoPrice and Amazon to get everything but the 6’ and 25’ MIDI cables.  I have other MIDI cables already and I have some F-F adaptors that can extend a couple cables.  I think that’s going to put me closer to the goal.  If not, I’m just wasting money, but what else is new?